Apart from the preeety picture, are there any actual problems with the motor? If not just drive it. Add zunc additive to every oil change from now on.

This to shall pass, a grind?

Nah my cast only washes with hot water and small Scraper. If you need soap. We’ll you don’t like actualy don’t. Seasoning? Just cook bacon, dump the grease leave a bit in put it back on the stove for a hot minute or while you put your blt together. Done it’s hunk of metal not much you can do to fuck it up. And if food is sticking to it probably cause you didn’t get the pan hot enough before you put the food in.

Oy yah i Rember the Repunzle tutorial.

I’ve been using a 1/4" thick sheet of carbon fiber for years now. Once warmed up to temp prints stick hard on it. As soon as it’s cool a breeze can push a print of the bed. Plus it won’t shatter like glass does eventually, boy was that a surprise. You still have to wipe clean with some rubbing alcohol before printing.

Bad bearing on a moving part. Or a bur along a rail, It catches just enough to cause the smooth motion to jitter a bit as the head moves along. Blobbing the material down instead of spreading it nice and even.

You have a draft going through your room, I used to have same issue when my printer was beside a window. Less when I moved the printer to middle of the room and issue was gone when put the printer into a closet. With closed doors.

You can try lowering bed temperature to, the warm bed keeps lower layer pliable but the upper layers cool and contract pulling the more flexible layer up and away. So a cooler bed temp should make the bottom layers more ridgid.

Amazing to assume that a franchise out in cottage country makes anywhere near the same revenue as one in down town toronto. What would you say is market wage? $20 per hour $25 per hour $35 per hour?

Lol Canadians don’t want those shit jobs to begin with.

You are a fucking monster. The point of this was to have some laughs not cause a poor walmart employee to beat their spouse or off them selves. Damn you’re cruel.

Dear-modern will find a way to make this in a 10/10 home

One of the most confusing places to be in is a Canadian machine shop. Half the machines will be imperial and the other will be metric. Work order come in both units on the regular.

You give the word power and meaning by viewing it certain way. To me cuss words have no power they are meaningless. equivalent to a simple filler word. Others around you might give power to cussing, but then why is it your fucking problem that they choose to be simps for a word?

Everyone worried about the bending force, the retaining slots will tear out and drop the damn thing on the desk well before it bends.

Yah this is bad I run a cnc plasma table, big table 10 feet x 20 feet. It uses floppy disks. Pain in the ass to find a new drive and pain in the ass to find new disks because constant write re write emf and metal dust kills them. But despite that it’s still cheaper and easier than a $15k retro fit to a more modern controler.

One weird trick that DOT doesn’t want you to know.

Now do it like 5 or 6 more times on the rest of the bed and now it’s textured for extra adhesion.

Can you post the g code ?

What printer do you use. This is a mechanical issue. It’s something binding as the one x or y is traveling could be a bearing or the stepper motor it self. It prevents the arc from being fully formed even though the machine thinks it is key point you made is that randomized z seam leaves the same mess, but if notice it’s not all the layers are cut short only some.

Take the belt off and move the axis by hand slow and easy do you feel anything that isn’t smooth like silk? That would be it. Feel the stepper is the drive gear tight any slip ?? Any play in the shaft side?

Edit

Looking at the pictures again I’d bet that if you went taller and printed faster, it would be even worse because the bad part got hotter and more bound up more Alternatively printing faster might make it better because you have the inertia to push past the binding spot.

Ig you think that’s bad wait until you get multiple retractions going that the rocking motion of the 3kg Is probably going to be enough to pull the filament right out of the extruder.