I really wish I could buy a new model control panel and put it on an old model so I can get useable diagnostics. (maybe I can?) Really hard to accept there is a water supply issue. It fills fine and it knows when to stop filling. The pump is fine, and also clear when I drain it and examine behind the drain plug. Surely if there were a water supply issue it would not fill the tub then decide after filling the tub and making some a few short fast spins that there is a water supply issue. I’ll pull out the water filter and see if anything looks sketchy. But I somewhat suspect the speed controller since the tumble (wash) cycle is way too fast.

I wish I had an error code but when it faults out it just gives a non-stop steady blinking LED. No variation that would indicated an error code.

Multimeters can be used to simply find out if a part is working. I recently used it when I lost hot water. By reading the voltage of the flow sensor, it was clear that the flow sensor bad (water running should give voltage X and still water should give voltage Y). I’m not sure how many such opportunities there are with washing machines though.

Thanks for the references. Looks dicey though. I thought maybe this archive might give docs that are close enough to my model, but I could not get past the CAPTCHA. It also looks like a lot of docs on that site are in a cryllic language. But I appreciate your effort nonetheless. If I seem to have no other option I might try to get around the CAPTCHA somehow.

Youtube is also rough going. There seems to be an ocean of useless Beko review videos and not much on repairing. Youtube’s protectionism makes them quite hard to use lately but if I can get past the obsticles I might look for repair videos on machines other than Beko and see if any of them help well enough.

There’s a point where it will be easier to toss the machine and get another but so far I’m trying to resist that.

yeah i tried unplugging from the wall. I don’t know if there is a separate motor controller board or if the motor controller is integrated into the same board with all the controls. I’m not sure how risky it is to replace the main controller board as a guess. I would like some certainty on where the fault is.

And maybe it is the motor. It looks like it spins fine to me, but if it’s at the edge of its life maybe it’s giving feedback to the controller that signals an issue with the motor.

In the case at hand, every function seems to work. When I start a program it starts by pumping water out from the last program. Tub fills with water fine. But at the start of the wash cycle it attempts a high-speed spin with a full tub of water, which seems quite bizarre. Attempting a high-speed spin with water in the tub causes it to jump because of all the weight. It /should/ just slowly rotate in one direction, then the other direction. But instead it does a 2 second spin then pauses for a minute. Then it repeats that 2 second high-speed spin then pauses. After 4 or so repeats of that it quits and leaves a blinking start button.

My first thought was that it detected overloading or an imbalanced load and maybe tried to balance the load. But it does the same thing empty. The belt is fine and the motor is obviously strong enough to make it spin as far as I can tell. But maybe something that controls the motor is broken. I am stuck because I don’t know how to probe the various parts with my multimeter as far as what readings I should look for.

The machine has a spin-only program that should do nothing but spin. When I run that program, it obviously does not add water. It just starts the spin (as expected) but pauses 2 sec after starting to spin… waits a min, then tries again. It looks like it spins fine but it’s giving up anyway.

Thanks. I had to translate it. It’s a troubleshooting guide for some common issues, but not my issue. I have the user manual for my model which has a troubleshooting table but it is not useful here.

I’m far from trying to track down the atomic component. I need to get an idea of what is failing. There should be readings I can take with the multimeter to see whether the motor is bad, or the controller for the motor, or something else. I’m not bothered at this point whether I can fix whatever part is broken. I might be fine with replacing a whole part. But I need to get there. I need to know which part is failing.

WMD 26125 T

I am so much more motivated than the typical consumer. My goal is that when someone else (your typical lazy consumer who may only care to get a refund) returns a can of worms to the grocery store, that the grocer have an obligation¹ to record the food quality/security issue and report it in a way that it gets tracked and ideally in a centralised place.

So indeed as I said, we need to evolve more. We have banks hyper-reporting on mere suspicion of something they perceive as off under excessive AML rules as if there is a gun to their head, yet you bring a real live creepy crawly to a grocer and there is minimal action… as you say getting swept under the rug as shrinkage.

¹ or pressure of some kind.

It’s something that should have been recorded and analysed. Perhaps they would discover something, like maybe they should inspect the rooibos before adding the white chocolate (if they are not already).

It might have had that, I don’t know; I don’t have the tin anymore. But indeed, we need to evolve more. Consumers are not going to pay to ship a tin to a producer. Store returns are managed by stores who potentially ship stuff back to their suppliers. In this case a bean-counter refused a return which then caused them to neglect to record a creepy crawly in their own food brand.

It was alive. It was in the tin for a while too. The tin had a tight fitting lid so there is no way it could have entered after I bought it and put it in my pantry. I did not discover it until about half the roobios was consumed.

(edit) just attached a pic to the OP.

Guess I should phrase it as a food security issue, not food safety, since security is broader and covers shortages. I probably got less “food” because that live worm has a lot more weight per volume than rooibos I was buying. Plus it probably ate some of it. So there’s my courtroom testimony ready to go :)

I did not reach out to them in this particular case. But I would expect Test Achats to focus on getting me a refund of 2 euros or whatever it is; I would not think Test Achats would do anything to intervene in quality control.

When I have contacted Test Achats in the past, they said something like subscribe to their magazine to become a member, then they will advocate for me on consumer issues. I decided not to subscribe.

Then a few years later I complained about at a consumer issue to a gov agency who then forwarded the complaint to ECCNET, which apparently is the same org as Test Achats. They responded to say they only handle cross-border problems and that anything that is entirely in Belgium (where both the consumer and merchant are in Belgium) is outside of their jurisdiction.

Glad to hear it!

This is a close-up shot:

https://lone.earth/w/7uFGbG6SZrUKiX1mFFT4NR

I thought it was dead at first but then it finally moved. It was perhaps nearly dead. I put it outside.

It’s two floors up from ground level. The sewer pipes are decent on that floor and the floor below AFAIK. On the ground floor the sewer pipes are certainly questionable and sometimes emit odors. I get lots of rain and in fact part of that results in slugs entering my ground floor kitchen. Not sure how they get in. Sometimes there are rats in the walls and basement, but never the living space.

I have no kids or pets that could have brought it in.

Thanks for the feedback!